Pricing

 

DOT SLEEPERS packages for your pickup truck $4500

Basic DOT sleeper berth: 33” deep, 37” high and 82” wide, sets on bed rails. There is an exit door (24”x 24”) on each side of the sleeper. Each door has latches and locks. A carbon monoxide detector installed. 2 way air vents installed. Seat belts on bed area with a 5” certified mattress. Accordion boot to connect sleeper to back window of your truck. Brake light wired when installed on sleeper. We spray on A RUBBER coating on the inside of the sleeper for better insulation and easy to clean.

The DOT Sleeper meets and exceeds D.O.T. guidelines for a sleeper berth.

* build a 3” angle iron frame same height to set & bolt sleeper on flat beds and chassis. Call for specific heights and instructions.

27” DEEP SLEEPER, 42” DEEP SLEEPER, 48” DEEP SLEEPER

* bottom storage (19”deep x 63.5” x 28.5”) for pick up trucks with box bed. This box is glassed together with the top sleeper so the unit is one complete unit ($1000)

* bottom storage for DOT on flat bed/chassis cut to size 82” wide. This box is glassed together with the top sleeper so the unit is one complete unit ($1500).

DOT Shell only is $2500


CAB HI SLEEPERS for your pickup truck

  • Looks like a box and is same height as your truck cab

  • All trucks: 32” deep sleeper $1600

  • All trucks: 42” deep sleeper $1900

  • All trucks: 48” DEEP SLEEPER $2400


ROAD RUNNER SLEEPERS for your pickup truck

  • The RR looks like a wedge design with aerodynamics to provide for smooth airflow over your truck.

  • Standard 73”x32” or 71”x32” $1600

  • Larger 73”x42” or 71”x42” $1900

  • XTRA large 48” deep $2400


ADDITIONAL OPTIONS for your order for your pickup truck:

  • Custom PAINT: to be determined and by an outside source starts at $700

  • INSTALLATION: $500-$700 on site by an outside source

  • Windows, tinted $200

  • Windows, large $300

  • Window: full lift style (special order)

  • Walk-in door with window 26”x 36” $800

  • DOT-solid Rear & side Doors 24” x 24” $550

  • Carbon Monoxide detector $100

  • 5” Foam Mattress Covered with certified label fits your sleeper size $250

  • INSIDE Light, battery powered (TBD)

  • INSIDE LED lights, 12 volt wired (TBD)

  • Brake light $75

  • WE CAN CUT DOWN ANY UNITS FOR 5TH WHEELS. Added fees

  • Baggage door $250

  • Removable floor to storage compartment $100

  • AC/HEAT unit 5000 btu can be ordered from www.climateright.com, we can cut the holes (3.5”)

  • 110 volt electrical plug outside to inside $150

  • Cigarette lighter or USB sockets $100

  • ¾” plywood in fiberglass roof for TV mount $200

  • metal frame added with eyelets to remove Sleeper from above $200

  • Bottom storage compartment (under sleeper) $1000

  • Set of Seat belts $75

  • Two way air vents (pair) $100

  • According boot for window $100

  • Jump seats w/ seat belts $350-$450

  • Bench w/2 seat belt sets $500 (pre-made and bolted to sleeper)

** *MEASUREMENTS: DOT FRAME measure from top of truck cab down 26”. That is the height of the 3” angle iron frame. Frame is to be same measurements as the sleeper being mounted (ex: DOT 33’x82”) Frame must be 1” from the cab


* NOTE:  All 1994 Dodge & up with accordion boot (except X cab with slider rear window) requires fiberglass frame where glass came out.  This applies only if window is glued in—truck with rubberized in window not affected. 

*NOTE:  All 1994 & up trucks (Rangers 93 & up) are required to have Centered BRAKE light.  

*NOTE: INSTALLATION KITS WITH FLAT STAINLESS STEEL PIECES PLACED UNDER THE RAILS $50.00 FOR PEOPLE DOING THEIR OWN INSTALL.